Eagle Shot Golf on SSV system board JAMMA Pinout

                          Main Jamma Connector
            Solder Side          |             Parts Side
------------------------------------------------------------------
             GND             | A | 1 |             GND
             GND             | B | 2 |             GND
             +5              | C | 3 |             +5
             +5              | D | 4 |             +5
                             | E | 5 |
             +12             | F | 6 |             +12
------------ KEY ------------| H | 7 |------------ KEY -----------
      Coin Counter # 2       | J | 8 |      Coin Counter # 1
      Coin lockout # 2       | K | 9 |      Coin lockout # 1
        Speaker (-)          | L | 10|        Speaker (+)
                             | M | 11|
        Video Green          | N | 12|        Video Red
        Video Sync           | P | 13|        Video Blue
       Service Switch        | R | 14|        Video GND
                             | S | 15|        Test Switch
        Coin Switch 2        | T | 16|        Coin Switch 1
  T:Not Used (J:P2 Start)    | U | 17|  T:Start        (J:P1 Start) 
  T:Not Used (J:P2 Up)       | V | 18|  T:Cursor Up    (J:P1 Up)
  T:Not Used (J:P2 Down)     | W | 19|  T:Cursor Down  (J:P1 Down)
  T:Not Used (J:P2 Left)     | X | 20|  T:Cursor Left  (J:P1 Left)
  T:Not Used (J:P2 Right)    | Y | 21|  T:Cursor Right (J:P1 Right)
  T:Not Used (J:P2 Shot)     | Z | 22|  T:Not Used     (J:P1 Shot)
 T:Not Used (J:P2 Decision)  | a | 23|  T:Not Used     (J:P1 Decision)
         Not Used            | b | 24|    Not Used
                             | c | 25|
                             | d | 26|
             GND             | e | 27|             GND
             GND             | f | 28|             GND

J= Joystick setting
T= Trackball Setting

2 Player inputs are only used when you set DIP Switch to
  "Joystick type" (DIP Switch 1, #6 to ON)

ATTENTION: At Trackball setting, 4 button wires go to "Up, Down, R, L"
           (pins 18, 19, 20, 21) on JAMMA connector.
           Do NOT wire to 22, 23, 24, 25 on JAMMA connector!


Connector Table for "Trackball Harness"
 same as the Golden Tee series harness

 JST Connector 6 pin (ROM Board Side)

  Pin  Wire  Funtion
------------------------------
   1 | RED | +5 Volts DC
   2 | YEL | X-A (Horizontal)
   3 | GRN | X-B (Horizontal)
   4 | BLU | Y-A (Vertical)
   5 | PUR | Y-B (Vertical)
   6 | BLK | Ground

 Connector 6 pin (Trackball Side)

  Pin  Wire  Funtion
------------------------------
   1 | BLK | Ground
   2 | RED | +5 Volts DC
   3 | YEL | X-A (Horizontal)
   4 | GRN | X-B (Horizontal)
   5 | BLU | Y-A (Vertical)
   6 | PUR | Y-B (Vertical)

NOTE: If your Trackball makes reverse movements for X and Y, you can
      exchange the pin position 3 and 4, or 4 and 5 to reverse at
      Trackball Connector side to correct.

BrianT